Park vehicle for at least 5 minutes (BN2000 and BN2020 vehicles) or 16 minutes (I-bus vehicle) with terminal R OFF so that all control modules can assume sleep mode, i.e. Perform vehicle test with the ISTA workshop system and end vehicle test on completion. Confirm the finishing off jobs individually.Įnter the time and date information to ensure correct calculation of the CBS values in the vehicle.Īfter programming, reinstall all removed or disconnected data media (DVD, iPod®, etc.) and check.Ĭompare the previously printed or noted CBS data of the control modules and,if necessary, reset and correct as part of the vehicle test in the ISTA workshop system. in the vehicle test in the ISTA workshop system as defined in the final report. Perform the finishing off procedures such as calibration, initialization, service functions etc. Fault codes may be entered and MOST control modules may be registered incorrectly if the ICOM is not correctly disconnected from the MOST direct access port. If an ICOM is connected to the MOST direct access port, disconnect the MOST direct access port when requested to do so by the ISTA/P system, remove the ICOM from the MOST ring and close the MOST ring with the original flash plug (bridge) in the vehicle. CAS)ģ.Do not cut the connection between workshop network, vehicle interface and vehicleĤ.Close the boot lid again after any action in the luggage compartment (e.g. loading/removing navigation DVD) to prevent the luggage compartment lighting from overheatingĥ.During programming, perform no other activities on/in the vehicle than those instructed by ISTA/P.ġ.Execute procedure for finishing off the measures plan and confirm by clicking “OK” Data media in a drive or still connected could cause programming to abortġ9.Before starting vehicle programming, make sure the boot lid is closed (to prevent the luggage compartment lighting from overheating).ġ.Observe and follow requests and instructions in ISTA/PĢ.Leave ignition switched on and follow instructions in ISTA/P (e.g. Make sure that the driver’s door contact is not operated during the programming procedure.ġ5.Perform a vehicle test with the ISTA workshop system to make sure that all installed control modules respond and any fault memory entries are read outġ6.Before programming, rectify any faults that may be present and delete any fault codes storedġ7.Determine CBS data, note down and end ISTA workshop systemġ8.Preparations: Remove inserted data media (DVD) and disconnect connected data (iPod®, etc.). Terminal 15 is permanently switched on by pressing the START-STOP button. − On vehicles with automatic terminal 15 shutdown (as from 03/2007) the signal from the door contact switches off terminal 15 by opening and closing the driver’s door. − If the vehicle model does not have an ignition lock, the identification transmitter must be located in the vehicle interior. The coding procedure may be terminated if the identification transmitter is not inserted in the ignition lock. − On vehicles with Comfort Access, the identification transmitter must be inserted in the ignition lock.
Cables routed through open windows could be damaged when the windows are started automatically.
Make sure that the vehicle system voltage does not drop below 13.0 volts while programming is in progressġ2.Set up connection between workshop network, vehicle interface and vehicleġ3.Check cable routing. Low system voltage may cause programming to cancel. Please refer to the operating instructions for the battery chargerġ1.Do not connect or disconnect the battery charger during programming. The battery charger connected during programming must be run in “external power supply mode with battery connected”.
Make sure that the wipers can move freelyĩ.Make a note of all stored radio and TV frequencies as well as the navigation destinationsġ0.Connect up a BMW Group-approved battery charger in the engine compartment. The wipers may be actuated during programming and initialization. 5.Activate electromechanical parking brake or apply parking brakeĦ.Make sure that the temperature of the transmission fluid is between -40 ☌ (-40 ☏) and 85 ☌ (185 ☏)ħ.Switch off all electric loads, lights and turn signal lampsĨ.Switch off wiper/washer system.